Smarteam

Chinese | English

Home page

Electromagnetic compatibility refers to the ability of electronic equipment to work harmoniously and effectively in various electromagnetic environments.

2024-01-26

The specific method is that one side of the printed board is wired horizontally, the other side is wired vertically, and then connected by metalized holes at the cross holes. 3, in order to suppress the crosstalk between the PCB circuit board wires, in the design of wiring should try to avoid long-distance equal routing, as far as possible to pull the distance between the line and the line

Electromagnetic compatibility refers to the ability of electronic equipment to work harmoniously and effectively in various electromagnetic environments. The purpose is to enable the electronic device to suppress all kinds of external interference, so that the electronic device can work normally in a specific electromagnetic environment, and at the same time to reduce the electromagnetic interference of the electronic device itself to other electronic devices.

1. Choose a reasonable wire width. Because the impact interference caused by transient current on the printed circuit board is mainly caused by the inductance component of the printed wire, the inductance of the printed wire should be reduced as much as possible.

2. Adopting the correct wiring strategy and adopting equal wiring can reduce the inductance of the wires, but the mutual inductance and distributed capacitance between the wires increase. If the layout allows, it is best to adopt a well-shaped mesh wiring structure. The specific method is to use one side of the printed board. Wiring, wiring longitudinally on the other side, and then connecting with metalized holes at the cross holes. 3, in order to suppress the crosstalk between the PCB circuit board wires, in the design of wiring should try to avoid long-distance equal routing, as far as possible to pull the distance between the line and the line

In 2017 Munich Shanghai electronic production equipment exhibition has been successfully exhibited, has been unanimously praised by the audience!

Recommended News

Electromagnetic compatibility refers to the ability of electronic equipment to work harmoniously and effectively in various electromagnetic environments.

The specific method is that one side of the printed board is wired horizontally, the other side is wired vertically, and then connected by metalized holes at the cross holes. 3, in order to suppress the crosstalk between the PCB circuit board wires, in the design of wiring should try to avoid long-distance equal routing, as far as possible to pull the distance between the line and the line

2024

01-26

In 2017 Munich Shanghai electronic production equipment exhibition has been successfully exhibited, has been unanimously praised by the audience!

Our company and three people were invited to participate in the global sales conference of battery tester held by Maccor company from November 13 to 16, 2023. During the few days of the trip, we deeply felt Maccor's position in the field of battery testing and its unremitting pursuit of innovation and technology. This trip was a substantial and unforgettable experience.

2024

01-26

The review group according to the "testing and calibration laboratory competence accreditation guidelines", "testing and calibration laboratory accreditation guidelines in the field of calibration application instructions"

Our company and three people were invited to participate in the global sales conference of battery tester held by Maccor company from November 13 to 16, 2023. During the few days of the trip, we deeply felt Maccor's position in the field of battery testing and its unremitting pursuit of innovation and technology. This trip was a substantial and unforgettable experience.

2024

01-26

Although the newly introduced 5V400A equipment is single-range, it has the accuracy of charging and discharging at a small current of 1A.

Our company and three people were invited to participate in the global sales conference of battery tester held by Maccor company from November 13 to 16, 2023. During the few days of the trip, we deeply felt Maccor's position in the field of battery testing and its unremitting pursuit of innovation and technology. This trip was a substantial and unforgettable experience.

2024

01-26

Maccor shares insights on battery performance, data analysis, and advanced features of the latest test instruments

Our company and three people were invited to participate in the global sales conference of battery tester held by Maccor company from November 13 to 16, 2023. During the few days of the trip, we deeply felt Maccor's position in the field of battery testing and its unremitting pursuit of innovation and technology. This trip was a substantial and unforgettable experience.

2024

01-26

The domestic research on the automatic detection system of printed circuit board began in the early and mid-1990s, and it has just started.

Our company and three people were invited to participate in the global sales conference of battery tester held by Maccor company from November 13 to 16, 2023. During the few days of the trip, we deeply felt Maccor's position in the field of battery testing and its unremitting pursuit of innovation and technology. This trip was a substantial and unforgettable experience.

2024

01-26

Invited to participate in the global sales conference of Battery Testers held by MACCOR

Colleagues from SMARTEM were invited to participate in the global sales conference of Battery Testers held by Maccor on November 13-16, 2023 in Tulsa USA.

2023

11-18

Participating the Productronica Shanghai

The Productronica Shanghai Expo was held as scheduled on April 13 at the Shanghai New International Expo Center. Tens of thousands of automatic equipment and Hi Tech innovations from all over the world dazzled across the exhibition floors.

2023

04-17

The central laboratory successfully passed the CNAS review

Hot column congratulates the world magotan central laboratory on passing the CNAS review. a group of 2 review experts from the China national accreditation Committee for conformity assessment conducted a 2-day CNAS on-site review of the central laboratory of Shenzhen branch of Beijing world magotan technology co., ltd. (hereinafter referred to as the central laboratory).

2022

03-18

Flying probe multi-function test platform to meet you 2018 Munich Shanghai electronic production equipment exhibition

The flying probe multifunctional test platform equipment newly developed and produced by Smarteam Company has been successfully exhibited at the 2017 Munich Shanghai Electronic Production Equipment Exhibition and has been unanimously praised by the audience!

2018

02-24

Copyright known as:SMARTEAM TECHNOLOGY Ltd. Powered by www.300.cn SEO View Business License

online message